Description
A 100% Pure Oil to mix with any Lubricant Oil and for NanoPolishing
16 oz. (476ml) NanoXD NanoCarbon is recommended for 4 to 6 cylinder engines with full lubricant oil capacity of up to 5 quarts
With NanoCarbon You Make the Best Investment in Your Vehicle
- REMOVE FRICTION
- REDUCE EMISSIONS
- IMPROVE PERFORMANCE
- REDUCE FUEL CONSUMPTION
LATEST GRAPHENE TECHNOLOGY!! For use on Autos, Marine and Jet Engine
For your 6 Cylinder vehicle:
- Apply product along with your next oil change
- We only need to apply it again every 4 oil changes, as the treatment will stay in the engine long after the oil is replaced
- Save up to 23% on fuel consumption.
- Reduce your Carbon emission
- Reduce your Engine wear and keep the engine in good condition for another 5 to 10 years
“Drivers on long trips have experienced between 12% and 22% less fuel consumption. Improvements observed on old cars, new cars and trucks with gasoline and diesel engines…” Check it the results at
$340.00Add to cart
INSTRUCTIONS for 1st Application:
- At first application, before applying the product, observe the current engine noise and vibration, which is noticeable in the hood of the vehicle, while the engine is running stationary (at idle speed)
- Apply NanoXD oil, through the main lubricant oil entry compartment, always considering 10% of NanoXD oil for total oil capacity of the engine.
- Fill-up the oil carter with your regular lubricant oil recommended by the manufacturer
- That’s it!
- However, if you want to get the benefits of NanoXD immediately, you must complete the treatment while the car is still parked:
- Turn-on the engine
- After 1 minute, increase the engine RPM slowly during a 5 minutes range until you reach 75% of max. RPM acceptable for your engine (Check your engine recommendation)
- Keep stepping on gas for up to 10 seconds
- At 75% max RPM, start slowly to decrease the RPM
- Slowly decrease to 50% of RPM and hold for 10 seconds
- Slowly decrease to 30% of RPM and hold for 10 seconds
- Slowly decrease to Idle engine and keep for 1 minute
- Finally, observe the reduction on engine noise and vibrations
- The engine will continue the treatment for the next 20 miles, continue to increase the performance and reduce fuel consumption even further.
- After 1 minute, increase the engine RPM slowly during a 5 minutes range until you reach 75% of max. RPM acceptable for your engine (Check your engine recommendation)
- Keep in mind that, if you DO NOT run the engine to reach 75% of your max RPM the product WILL NOT act in the engine and NO Benefit will be achieved until that actually happens while driving the vehicle on similar RPM as stated above.
- Turn-on the engine
INSTRUCTIONS for Any Future Application:
- Apply NanoXD every 4 oil changes or every 60k miles.
- NanoCarbon particles stick to the internal parts of the engine (with protection layer the size of 1 single atom) and will stay there even after a few oil changes
- The engine only requires re-application after 3 other complete oil changes or after 60,000 miles whichever occurs first,
- For commercial vehicles, which have controlled RPM and speed limit, it’s recommended to conduct the same treatment above described while vehicle is still stationary
Achieve results fast:
- Save from 13% to 23% on fuel consumption.
- Fuel Savings can reach up to $2,000 in 4 year, when driving more than 15K miles p/year
- Reduce your Carbon emission
- Reduce your Engine Wear and keep the engine in good condition for another 5 to 10 years.
Create Your Own Green Revolution While Saving Money on your Vehicle:
- BE A GOOD CITIZEN. Help The Environment while Lowering Your Cost of Fuel and Emission Controls
- Reduce Carbon Footprint, Carbon Emission and Fuel Consumption.
- NanoCarbon eliminates up to 90% of Engine Wear
- Helping you to Reduce Carbon Emission while saving money.
- A 2009 study found health costs of $153 million a year as a result of emissions from truck diesel pollution from a single Port of Oakland (CA) (source EDF – Environment Defense Fund).
Reviews
There are no reviews yet.